AntMiner s9 s9j s9i firmware

Alternative firmware allows you to fully discover all the possibilities of your miner!

Bitmain Antminer S9 (12.5-13-13.5-14Th/s)
Bitmain Antminer S9i (14-14.5TH/s)
Bitmain Antminer S9j (14-14.5TH/s)
For all S9 model with Xilinx CPU control board. Not support C5 control board.

Antminer-S9-S9i_v004x(beta10).tar.gz
md5: d73727215411421807a821ebf8645a9a
sha1: 8d3087c601a2c30a9325d10ae8a0f9816ddff41f

Antminer-S9_to_S9i_patch.tar.gz
md5: 1816e4838c88f9a07521195ff50f6740
sha1: 8ab195d385d4bfd460138c9d0583325f03c9e2a6

Antminer-S9_to_S9j_patch.tar.gz
md5: 439aed0efe8402bc838689146ec2a45a
sha1: 8dfbebe8a083976c6067b9adab7b5c77cfabbb34

Manual

The firmware from asicfw.io is available for download free of charge, but it has a Dev Fee of 1.3% -2% (mining is not interrupted, the dev fee works parallel to the main mining). The firmware from asicfw.io makes it possible (with the same consumption as standard firmware from Bitmain) to get more computing power and extend the life of AntMiner 5 times due to the tuning of each chip separately.

AntMiner s9 / s9i / s9j firmware from asicfw.io fits all models. The first custom firmware with AsicBoost S9 saves up to 250W on pools that support AsicBoost technology (slushpool, antpool, btc.com, f2pool and others).

The design is made as similar as possible to the original one for more convenient use.

The firmware is installed in a standard way.

The firmware AsicFW.io for S9 / S9i / S9j with control of each hashboard’s frequency, voltage and overclocking templates up to 18 + TH in the air and 19-22TH in immersion cooling. (Be careful, the overclocking requires a more powerful power supply. You can use 2 standard power supplies or 3 standard power supplies (1600W) for 2 Antminers – You must not connect one hashboard to two different power supplies!

  1. Fan check disable for immersion into the immersion cooling.
  2. Manual change of the fan speed in % or auto.
  3. Enable or disable the AsicBoost feature.
  4. Enable or disable low-noise fan auto mode.
  5. Change the frequency of all hashboards.
  6. Change the Voltage of all hashboards.
  7. Change the frequency of each hashboard individually.
  8. Change the Voltage of all hashboards.
  9. Watchdog - reboot when reaching the set temperature.
  10. Watchdog - restart when the hashrate drops.
  11. Reset.
  12. Save and apply.

- The Watchdog function allows you to automatically configure a reboot when the hashrate drops and when the set temperature is reached.

  1. Auto tuner profiles depending on power consumption.
  2. Available in Manual - minimum frequency value. At this value the Auto tuner finishes tuning.
  3. Available in Manual - maximum frequency value. From this value the Auto tuner starts tuning.
  4. Available in Manual - minimum Voltage for Auto Tuner.
  5. Available in Manual - with this value the Auto tuner starts tuning the Voltage.
  6. Available in Manual - setting in % the amount of chips on the hashboard that work perfectly when changing the Voltage settings.
  7. Available in Manual - time in seconds for CGMiner restart while the Auto tuner is being set.
  8. Available in Manual - Auto tuner check duration.
  9. Available in Manual - statistics poll interval.
  10. Chip tuning section.
  11. Running Auto tune chips that are not working perfectly.
  12. Time in minutes for restart.
  13. Frequency step auto tune settings.
  14. Maximum amount of restarting auto tune chips.
  15. Save and run auto tune settings.
  16. Save and run only auto tune chips.

Manual mode is not recommended to be used by ordinary users!

More information in Manual AntMiner S9 .pdf

INFO

info@asicfw.io

ADDRESS

Australia, 4217 Gold Coast, Queensland, 3171 Surfers Paradise Blvd

Partners

SOCIAL